How to Build a Bike Ramp in 7 Quick & Easy Steps (W/Photos)

Building a bike ramp is a quick and easy process that can be done in seven steps. First, find a level spot to build the ramp on. Next, use stakes and string to mark out the shape of the ramp.

Then, cut the lumber for the frame of the ramp according to your measurements. After that, assemble the frame and secure it with screws or nails. Finally, attach plywood or OSB board to the frame to create a smooth riding surface.

Once everything is secure, test out your new ramp by riding down it!

  • Decide on the location and size of your ramp
  • Sketch out a basic design for your ramp
  • Gather the materials you’ll need to build your ramp, including lumber, plywood, decking screws, and concrete mix
  • Cut the lumber to size according to your sketch and screw it together to create the frame for your ramp
  • Cover the frame with plywood and attach it with decking screws
  • Pour concrete into any holes or depressions in the ramp surface and smooth it out with a trowel so it’s level with the rest of the ramp surface
  • 7) Let the concrete dry completely before using the bike ramp!


How to Make a Simple Bike Ramp?

If you’re looking to add a little excitement to your biking repertoire, or simply want an easier way to get down your driveway, consider building a simple bike ramp. With just a few supplies and some basic carpentry skills, you can have a sturdy ramp built in no time. Here’s what you’ll need:

-4×8 sheet of plywood -2x4s (8ft long) -Circular saw

-Drill -1 inch hole saw -Jigsaw

-Paint or sealant (optional) Step 1: Cut the Plywood Using the circular saw, cut the 4×8 sheet of plywood into two equal pieces lengthwise.

These will be the sides of the ramp. Step 2: Cut the 2x4s Next, use the drill and 1 inch hole saw to cut four holes in each 2×4, spaced evenly apart.

These will be used to bolt the 2x4s together later on. Step 3: Assemble the Frame Lay out two of the 2x4s on flat ground, parallel to each other and spacing them about 3 feet apart.

Place one of the plywood boards on top of these so that it sits flush with the edges of the 2x4s. Next, take two more 2x4s and place them perpendicular atop this assembly, again making sure that they are flush with all edges. Now bolt everything together using washers and nuts at each of the holes drilled earlier. Repeat this process for assembling the other side panel. You should now have two A-frame structures – these will be your ramps! Step 4: Add Crossbeams To add stability and keep your ramps from spreading apart while in use, it’s important to add some crossbeams between them . Cut four more 2x4s to lengths that correspond roughly with half the distance between each uprights on either side panel – these will serve as your crossbeams . Place them atop your frame so that they intersect in the middle , then bolt or screw them into place . Trim any excess lumber off so that everything is even . Step 5 : Attach Ramp Boards The last step is attaching your riding surface !

What is the Best Angle for a Bike Ramp?

There is no definitive answer to this question as the best angle for a bike ramp will depend on a number of factors, including the size and shape of the ramp, the type of terrain it will be used on and the rider’s personal preferences. However, as a general rule of thumb, most experts recommend building ramps with an angle of around 15 degrees. This should provide enough slope to allow riders to get up and over obstacles without being too steep or difficult to maneuver.

How Do You Build a Mountain Bike Ramp?

Building a mountain bike ramp is not as difficult as it may seem. With a little bit of planning and some elbow grease, you can have your very own jump park in no time! Here are the basic steps to building a mountain bike ramp:

1. Choose the location for your ramp. You’ll want to pick a spot that’s flat and level, with plenty of room around it for riders to approach and land. 2. Sketch out your design on paper, or use an online Ramp Builder tool like this one from

This will help you visualize the size and shape of your ramp, and determine how much material you’ll need to build it. 3. Gather your supplies. For most ramps, you’ll need plywood, 2x4s, deck screws, concrete mix, and rebar or steel tubing for reinforcement (optional).

4’x8′ sheets of 3/4″ plywood are a good starting point – you can always cut them down if needed. 4. Build the base of your ramp using 2x4s or 6x6s fastened together with deck screws (or nails). The base should be at least 10 feet wide for stability.

If you’re using concrete mix, wet the wood first so it doesn’t absorb all the moisture from the mix. Fill any gaps between boards with more concrete mix before letting it set up overnight. 5 To make the transition (the curved part that leads up to the lip), attach two sheets of 3/4″ plywood together at an angle with deck screws or nails spaced about 6 inches apart along the edges (image below).

Cut out any excess wood so that only the curved transition remains – this will make it lighter and easier to maneuver when riding.. 6 Attach your transition to the base using more screws or nails spaced about 6 inches apart along both edges (image below).

Again, fill any gaps with concrete mix before letting it set up overnight.. 7 To finish off the lip, either attach another sheet of 3/4″ plywood on top of the transition using screws or nails spaced about 6 inches apart along both edges; OR cut two 2x4s or 4x4s into 12-inch lengths and screw them onto either side of the transition for added support.. 8 Once everything is dry, give your ramp a test ride!

How High Should a Bike Ramp Be?

There is no definitive answer to this question as it depends on a number of factors, such as the type of bike, the terrain, the rider’s ability level, and so on. However, a good rule of thumb is that a bike ramp should be at least 3 feet high in order to provide enough clearance for the wheels to safely roll over obstacles.

How to Build a Bike Ramp in 7 Quick & Easy Steps (W/Photos)


Simple Bike Ramp Design

Bike ramps are a great way to get your bike up and over obstacles. But, how do you choose the right bike ramp for your needs? Here are a few things to consider when choosing a bike ramp:

– The height of the obstacle you need to overcome. The taller the obstacle, the longer and steeper the ramp needs to be. – The width of the obstacle.

If the obstacle is wide, you’ll need a wider ramp. – The weight of your bike. Heavier bikes will need stronger ramps that can support their weight without collapsing.

– The surface of the ramp. Smooth surfaces are best for riding on, but rougher surfaces can provide more traction if needed. With these factors in mind, here are some simple bike ramp designs that you can use to get your bike over obstacles:

1) A-Frame Ramp: This design is good for overcoming tall obstacles. It’s made by attaching two pieces of wood at a 90 degree angle so that they form an “A” shape. Then, nail or screw them together at the top and bottom so they’re sturdy.

To use this design, simply place one end of the ramp on the ground and lean it against the obstacle you need to overcome. Then ride up the Ramp and over the top! 2) Curved Ramp: This design is good for overcoming shorter obstacles that are also wide (like stairs).

It’s made by attaching two pieces of wood together at one end using screws or nails. Then, curve them away from each other so they form a “U” shape . To use this design, place one end of the “U” onthe ground and position it next tothe obstacle you want to overcome . Then , roll your bike up onto the Rampand push off with your feetto go overtop! 3) Straight Ramp: This design is good for overcoming small obstacles like curbs . It’s made by attaching two pieces of wood together side -by -side using screws or nails .To use this design , simply placeone endoftherampon the groundandpositionittotheobstacleyouwant toovercome ,thenrideupandoverwithyourbike !

Bike Ramp for Kids

If you have kids who love to ride bikes, you may be looking for a way to make it easier for them to get around. A bike ramp is a great solution! Bike ramps can help your child get up and down the driveway or sidewalk, and they’re also great for doing tricks.

Here are some things to consider when choosing a bike ramp for your child: Size: Make sure the bike ramp is big enough for your child’s bike. Some ramps are made specifically for scooters or skateboards, so double check before you buy.

Material: Most bike ramps are made of plastic or metal. If you choose a metal ramp, make sure it has a smooth finish to avoid scratches on your child’s bike. Plastic ramps may be lighter and easier to carry, but they can crack if they’re not used properly.

Weight limit: Check the weight limit on the ramp before you buy. You don’t want your child’s bike to be too heavy for the ramp! Setup: Some ramps come pre-assembled, while others need to be put together yourself.

If you choose a self-assembly ramp, make sure the instructions are clear and easy to follow.

Diy Bike Ramp for Stairs

A bike ramp for stairs is a great way to get some exercise and fresh air, while still being able to enjoy the scenery. It can be a great addition to any home, and it’s not as difficult as you might think to build one yourself. With a little bit of planning and some basic tools, you can easily construct a DIY bike ramp that will provide years of enjoyment.

The first step is to decide where you want to locate your ramp. It’s important to choose a spot that is level and free of obstacles. Once you have a location in mind, mark out the area with stakes or string so you know where to begin digging.

Next, start excavating the soil within the marked perimeter. You’ll want to make sure the hole is deep enough so that the ramp will sit flush with the ground when it’s finished. As you dig, add support beams around the perimeter of the hole – these will help keep the sides from caving in as you continue digging.

Once the hole is dug, it’s time to start building the frame for your ramp. Again, use stakes or string to mark out where each beam will go. Cut each piece of lumber to size and then nail or screw them into place.

Make sure everything is level and square before moving on to the next step. Now it’s time for fill dirt – this will form the base of your ramp. Add fill dirt until it reaches about 2 feet high, then pack it down firmly using a hand tamper or similar tool.

Once everything is nice and level, cover the fill dirt with landscape fabric (this will help prevent weeds from growing). Now you can add your riding surface – this can be anything from concrete pavers to interlocking tiles designed specifically for outdoor use. Start at one end of your ramp and work your way up, making sure each piece fits snugly against its neighbors (you may needto cut some pieces to size).

Once all of your tiles are in place, give them a good 24 hours to set before using your new bike ramp!

How to Build a Bike Jump Out of Wood

Building a bike jump out of wood is a great way to get into BMX riding. It’s also a relatively easy project that can be completed in a weekend with just a few tools and some basic carpentry skills. Here’s how to do it:

1. Start by finding a suitable location for your jump. You’ll need enough space to build the jump, plus room to land and ride away safely. Once you’ve found the perfect spot, mark out the dimensions of the jump with stakes and string.

2. Next, it’s time to start building the jump itself. The frame of the jump will be made from 4×4 lumber, so cut eight pieces to size using a saw. Then, attach the pieces together using screws or nails and make sure everything is level and square.

3. To finish off the frame, add some crossbeams for reinforcement. Cut four more pieces of 4×4 lumber and attach them perpendicular to the main frame beams. Now you have a sturdy structure that’s ready for jumping!

4. The next step is to add plywood sheets to both sides of the frame in order to create a smooth riding surface. Secure the plywood with screws or nails, making sure everything is level and flush before moving on. 5.,The final step is to cover the plywood with something durable like carpeting or Astroturf .

Diy Bike Loading Ramp

When you start talking about loading your bike onto a vehicle, the first thing that comes to mind is probably a loading ramp. But what if you don’t have one? Or what if you want to avoid the hassle and expense of buying or renting one?

If you’re handy, you can build your own bike loading ramp with some basic materials and a little bit of know-how. The most important part of any bike loading ramp is the surface. It needs to be smooth so that your tires don’t get caught on anything as you’re rolling up.

Plywood is a good option, but if you have access to aluminum sheeting, that will work even better. Just make sure that whatever material you use is securely attached to the frame of your ramp. Next, you’ll need something to act as supports for your ramp.

2x4s or 4x4s are ideal for this purpose. Cut them to length so that they’re slightly longer than the width of your ramp surface. Attach them perpendicular to the ramp surface at each end, using screws or nails.

Now it’s time to add some traction to your ramp surface. This will help keep your tires from slipping as you roll up. There are a few different ways to do this:

– You can attach strips of sandpaper or other abrasive material with double-sided tape or glue. – You can buy special non-slip tapes or mats that are designed for this purpose (these can be found at most hardware stores). – Or, my personal favorite method, which is sprinkling generous handfuls of cat litter over the entire surface of the ramp (just make sure it’s unscented!).

The tiny pieces of clay will grip your tires nicely and won’t slip around like sandpaper can. Plus, it’s much less expensive than buying special tapes or mats! Once your traction material is in place, give the whole thing a test run before Loading up your precious cargo!

How to Build a Bmx Ramp

Building a BMX ramp can be a fun and rewarding experience, but it takes some planning and work to get it done right. Here are the steps you need to take to build a successful BMX ramp: 1. Decide where you want to build your ramp.

This is important because you need to make sure you have enough space for the ramp and that it will be safe to use. 2. Choose the materials you want to use. There are many different options available, so do some research to find the best material for your needs.

3. Gather all of the tools and supplies you need before getting started. This will make the process go much smoother and help you avoid making mistakes. 4. Follow the instructions carefully as you assemble your ramp.

Pay attention to all of the details so that everything fits together correctly and securely. 5. Once your ramp is complete, test it out to make sure it’s safe and sturdy before using it for real tricks or jumps!


Building a bike ramp doesn’t have to be complicated or time-consuming. With just a few materials and some basic tools, you can build a simple ramp in no time. Here’s a quick and easy seven-step guide to get you started.

1. Choose your location: You’ll want to pick a spot that’s level and clear of any obstacles. A driveway or patio is usually a good choice. 2. Gather your materials: For this project, you’ll need some plywood, 2x4s, screws, and nails.

You can find all of these at your local hardware store. 3. Cut the plywood: Measure and cut the plywood into two pieces that are the same length as your 2x4s. These will be the sides of your ramp.

4. Assemble the frame: Nail or screw the two pieces of plywood to the 2x4s to create a basic frame. Make sure everything is square and level before moving on to the next step. 5. Add supports: Cut additional 2x4s to use as supports underneath the frame of your ramp (these will help prevent it from sagging in the middle).

Attach them using screws or nails . ;You may want to add more than one support depending on how long your ramp is going to be . 6 .

Cover with decking : Once ;the supports are in place , cover ;the frame with more plywood or decking boards . This will give ;the ramp a smoother surface for riding . 7 .

Finish up : Trim off any excess material , then sand down any rough edges . If desired , paint or stain ;the ramp before using it . That’s it!

Leave a Comment