If your chain has come off, it is likely because the derailleur (the mechanism that moves the chain between gears) has moved out of alignment. To fix this, first make sure that the derailleur is in the correct position (it should be lined up with the smallest cog on the cassette). If it is not, use the barrel adjuster to move it until it is.
Once the derailleur is in position, you can put the chain back on by hand or with a chain tool.
To put the chain back on by hand, thread it through the derailleur and around the largest cog on the cassette. Then, holding onto both ends of the chain, pull until there is no slack.
The last link of the chain should line up with the first link (this is called a master link). You can now connect these two links using a quick release lever or a master link.
To put the chain back on with a chain tool, thread one end of the chain through the derailleur and around the largest cog on The second method for putting a bicycle Chain Back On Is to use a Chain Tool; First you will need to find which way th echain needs to go onto eithe rthe big ring our small ring ,if its going onto teh small ring infront then you will also needto place It Onto The Smallest Sprocket At The Rear As Well ,once you have done that take teh loose end od teh chanin and push It Into THe jaws Of Teh Chain Tool making surethat Its Facing The Right Way round so when tightened It doesnt come undone itself .
Once In Place start tightening teh screw at teh topof tjheChain Tool Until THe Pin Comes Out At THe Other Side Of THe Link Pushing THrough One Of TH eO RIngs ,you might needto wiggleIt A Little Bit To Get IT Started But DOnT FORCE IT AS THIS CAN DAMAGE THE TOOL OR THE CHAIN ITSELF !
- Unhook the chain from the derailleur
- Place the chain on the sprocket, making sure that all of the teeth are engaged
- Pull the chain tight and hook it back onto the derailleur
- Test ride your bike to make sure that the chain is seated correctly and is not slipping off of the sprocket
How Do I Stop My Chain Jumping? | GCN Tech Clinic
How Do You Put a Bike Chain Back on a Bike?
If you have ever wondered how to put a bike chain back on a bike, wonder no more! It is actually quite simple, and only takes a few minutes. Plus, it is a great way to save money by not having to take your bike to the shop every time the chain falls off.
Here is what you need to do:
1) Flip your bike over so that the wheels are in the air. This will make it easier to work on the chain.
2) Find the master link. This is the link that holds the two ends of the chain together and makes it possible to remove and replace the chain without tools. It will look like a small oval with an open side.
3) If your master link does not have an open side, then you will need to use a pair of needle nose pliers or other small tool to push out one of the pins holding the link together. Be careful not to lose this pin!
4) Once you have removed the master link (or opened it up), slide it out of one end of the chain.
Now you can pull the rest of the chain off of the bike completely.
5) To put the new or repaired chain back on, simply feed it through all ofthe gears starting atthe pedalsand working your way back towardsthe rear wheel sprocket(s). Make sure thatthe teethof each gear are properly meshedwith thoseofthechainbefore continuingto avoid damagingyour equipment.
6) Whenyou reachthe endofthechain, reattachthemasterlink(or reconnectoneofthepinsif necessary),and testitby pedalingforwarda few timesbefore gettingbackontheroadagain!
How Do You Put a Loose Bike Chain Back On?
Assuming you have a derailleur-equipped bike, here are the steps to put a loose chain back on:
1. First, identify which chain ring the chain has come off of. If the chain is hanging down and not touching either wheel, it’s most likely come off the innermost ring (the one closest to the frame).
2. Next, line up the teeth on the chainring with those on the derailleur cage. You may need to wiggle things around a bit to get everything lined up perfectly.
3. Once everything is lined up, gently push the chain onto the teeth of the ring until it clicks into place.
4. Now that the chain is back on track, pedaling will cause it to tighten up automatically – no need to fiddle with any bolts or screws!
How Do You Put a Chain Link Back On?
If your chain has come off, don’t worry! It’s a relatively easy fix. Here’s how to put a chain back on a bike:
1. First, thread the chain through the rear derailleur. Make sure that the chain is going around the largest cog in the rear cassette (the gear cluster at the back of the bike).
2. Next, take the chain and thread it through the front derailleur (this is the mechanism that shifts gears at the front of your bike).
Again, make sure that the chain is going around the largest ring on your crank set.
3. Now it’s time to connect the two ends of the chain together using a master link or a Quick Link. A master link is a special connector that can be opened and closed without tools, while a Quick Link requires a pair of needle-nose pliers to open and close.
If you’re not sure which type of connector you have, consult your bike’s owner’s manual or take it to your local bike shop for assistance.
4. Once you have connected the two ends of the chain together, give it a quick tug to make sure that it’s secure before taking your bike out for a spin!
How Do You Put a Bike Chain Back on a Derailleur?
Assuming you are asking how to put a chain back ONTO a derailleur:
1. Thread the chain through the rear derailleur. There are typically two ways to do this, from above or from below.
If threading from above, pull the chain around the top pulley wheel on the derailleur, and then loop it underneath the tension spring (located at 11 o’clock). If threading from below, pull the chain up and over the bottom pulley wheel (located at 1 o’clock), and then over/around the tension spring. In both cases, make sure that as you’re pulling the chain through that you hear/feel it “click” into place so that it’s locked in.
You’ll know it’s locked in because you won’t be able to pull it any further through without putting pressure on it (i.e. using your fingers to push/pull).
2. Next, take one end of the chain (it doesn’t matter which) and insert it into one of the links on your cassette (the gears located on your rear wheel). Inserting a link into your cassette is easy – just line up an open link with an empty space between two teeth on your cassette, and then push down until you feel/hear it snap shut.
Make sure that when you close the link, both sides of the “chain” part are facing outwards – if they’re not, then your chain will rub against itself while pedaling and eventually break.
3. Now do step 2 again but this time with the other end of your chain – insert one end of your chain into another open link on your cassette until you feel/hear it snap closed. And that’s it!
Credit: www.orlando.gov
How to Put Chain Back on Mountain Bike
If you’ve ever had to put a chain back on a mountain bike, you know it can be a pain. The good news is, it doesn’t have to be! With a little bit of patience and the right tools, you can get your chain back on in no time.
First, start by putting your bike in the stand. This will make it easier to work on and prevent the chain from falling off while you’re working. Next, use a chain tool to remove the old chain.
If you don’t have a chain tool, you can also use a pair of pliers.
Once the old chain is removed, it’s time to put on the new one. Start by feeding one end of the chain through the front derailleur.
Then run the chain around the cassette and through the rear derailleur. finally, connect the two ends of the chain using a quick link or master link.
Now that your new chain is installed, it’s time to adjust its tension.
The easiest way to do this is with a derailleur hanger alignment tool. Simply insert the tool into one of the links and rotate it until there is no longer any slack in the system. You may need to readjust as you ride, but this should get you started!
How to Thread Chain Through Rear Derailleur
Chain derailment is one of the most common bicycle maintenance issues. It can be caused by a number of factors, but most often it is simply due to poor chain alignment. The rear derailleur is responsible for moving the chain from one sprocket to another, and if it isn’t properly aligned, the chain can easily come off.
There are two different types of rear derailleurs: threaded and non-threaded. Threaded derailleurs have a small hole in the back plate that allows you to thread the chain through. Non-threaded derailleurs don’t have this hole, so you’ll need to remove the back plate in order to thread the chain.
Assuming you have a threaded rear derailleur, here’s how to thread your chain:
1. Put your bike in its lowest gear so that the chains are tightest. This will make it easier to thread the chain through the derailleur.
2. Unhook the old chain from around your largest cog in the back (this may require using a master link pliers). You should now be able to see the small hole in your back plate where you’ll be inserting your new chain.
3. Take one end of your new chain and thread it through that hole until about half of it has gone through (you may find it helpful to use a small pick or other sharp object to guide thechain through).
4a) If your new chain has a master link: once half of it is through, putthe master link onto one side ofthe exposed partofchain, then takethe othersideand hookit intothe otherendofthe masterlink(oppositeof whatyou just did).
Mountain Bike Chain Fell off
If you’ve ever been mountain biking, you know that it can be a rough ride. And one of the most frustrating things that can happen is when your chain falls off.
There are a few different reasons why this might happen.
First, if your chain is old or worn, it might not be tight enough and could come loose. Second, if your bike hits a bump or branch just right, the force could dislodge the chain. Third, if you change gears too quickly, the chain can come off.
Whatever the reason, it’s important to know how to fix it so you can get back on the trail as soon as possible. Luckily, it’s not too difficult to put the chain back on – here’s how:
1. Put your bike in an easy gear so you’ll have more leverage when pedaling.
2. Find the end of the chain that has a master link – this is the link that allows you to take the chain on and off without using a tool.
3. Line up the master link with both ends of the chain and push it together until it clicks into place (it should look like a figure eight).
4. If your master link doesn’t have a locking mechanism, use a pair of needle nose pliers to squeeze each side of the link together until it’s secure.
5 . Once your master link is in place, pedaling in an easy gear will help tighten up any slack in the chain so don’t forget to do this before heading back out on the trail!
Conclusion
ca
If your bicycle chain has come off, don’t worry! It’s actually quite easy to put it back on.
First, find the loose end of the chain and thread it through the rear derailleur. Then, pull the chain tight and join the two ends together with a quick link or master link. Finally, route the chain through the front derailleur and onto the bike’s gearset.
With a little practice, you’ll be putting your bicycle chain back on like a pro in no time!