How to Put a Chain on a Mountain Bike – A Detailed Guide

If your mountain bike doesn’t have a derailleur, then it probably has a freewheel, which means that the chain runs freely on the sprockets. To put a chain on a mountain bike with a freewheel, you’ll need to thread the chain through the rear triangle and around the sprockets. The easiest way to do this is to put the bike in a stand so that you can rotate the pedals and sprockets.

Start by threading the chain through the rear derailleur (if there is one), then around the largest sprocket on the cassette. Continue running the chain around the smaller sprockets until you reach the smallest sprocket. Now thread the chain through the front derailleur (if there is one) and back tothe largest sprocket.

You may need to use a chain tool to remove some of links fromthechain before it will fit properly.

  • Place the bike on a level surface and shift it into the smallest cog in the rear
  • Unscrew the bolt that’s holding the old chain in place with a chain whip and pliers
  • Take off the old chain, clean any rust off of it, and measure it to see if you need to remove any links
  • To remove links, use a chain tool to push out the pins that hold them together
  • Put the new chain around the cassette (rear gears) and then thread it through the derailleur cage
  • Join the two ends of the chain using a quick link or master link, and make sure that it is tight against both sides of the cog before trimming off any excess links

How To Replace A Mountain Bike Chain | Change Your Chain Like A Pro

How Do You Put a Mountain Bike Chain On?

There are a few things you need to do in order to put a mountain bike chain on. You will need a chain, a chain tool, and some patience. The first thing you need to do is remove the old chain from the bike.

Use the chain tool to push out the rivet that holds the pin in place. Once the old chain is removed, clean off any dirt or grime that has built up on the teeth of the cogset and derailleur pulleys. Next, take your new chain and thread it through the derailleur Pulleys starting with the tensioner pulley (if your bike has one).

At this point, you will want to make sure that the new chain is of proper length. To do this, shift your bike into its largest gear combination in both front and rear then add two links to your new chain. This will ensure that there is no slack in your system when shifting under load.

Once you have verified that your new chain is of proper length, use the Chain Tool to push a new rivet through one end link of your Chain.Leave about 1/8” of space between where The Pin rests against The Plate inside The Link (this space allows for expansion as The Chain warms up with use). Hand-tighten The Nut until snug against The Outside Plate then use The Lever arm on The Chain Tool body To finish tightening The Nut until secure (You Should Not Be Able To Pull The Pin From This Side Of The Link). Repeat this process at the other end of yourChain

Your mountain bike’s drivetrain is now ready for action!

How Do You Attach a Chain Guide?

There are a few different ways to attach a chain guide, depending on the type of bike you have and the specific guide you’re using. In general, though, most guides will either clamp onto your frame or seatpost, or be attached with zip ties. If your guide clamps onto your frame, you’ll first need to remove any existing bolts from the spot where the guide will go.

Then, line up theguide so that the teeth are facing inwards and align with your chainring. Once it’s in place, use the included bolts to secure it to your frame. If your guide attaches with zip ties, start by wrapping one around your frame tube and threading it through the hole in the back of the guide.

Pull it tight and cinch down with a second zip tie. Repeat on the other side. You may need to adjust the placement ofthe guide once it’s all tightened down so that the teeth are properly aligned with your chainring.

How Do You Make a Mountain Bike Chain Guide?

A chain guide is a device that helps to keep your bicycle chain from falling off of the gears. There are several different types of chain guides, but they all essentially work in the same way. To make your own mountain bike chain guide, you will need some basic materials and tools.

The first step is to gather your materials. You will need a length of plastic or metal tubing, a piece of plywood or cardboard, and some adhesive. You will also need a drill, a saw, and some handtools.

Next, cut the tubing to size using the saw. It should be long enough to reach from the bottom bracket to the top of the front gear cluster on your bicycle. Cut two pieces of plywood or cardboard to fit snugly inside the tubing.

These pieces will act as end caps for your chain guide. Now it’s time to assemble everything. Drill holes in both pieces of plywood or cardboard, and then thread the tubing through them.

Make sure that the tubing is centered in each piece before you glue them together with the adhesive. Once everything is dry, you can attach your mountain bike chain guide to your frame using bolts or zip ties.

Do You Really Need a Chain Guide Mtb?

If you’re a mountain biker, chances are you’ve been asked this question before: “Do I need a chain guide on my bike?” The answer, as with most things related to cycling, is that it depends. Here’s a look at when you might need a chain guide and when you might not.

First, let’s start with what a chain guide does. A chain guide is a device that mounts to your frame and helps keep your chain from falling off the front or rear cog while you’re riding. It’s especially useful if you’re riding in rough terrain where there are lots of obstacles that could cause your chain to come off.

Now, let’s talk about when you might need a chain guide. If you ride in very rough terrain or do any type of downhill mountain biking, then it’s probably a good idea to have one. Chain guides can also be helpful if you ride with really low tire pressure (under 20 psi) because they help prevent the tires from coming off the bead and causing flats.

They can also be helpful if you have an unconventional drivetrain setup like a 1×11 or 2×10. On the other hand, there are some situations where you probably don’t need a chain guide. If you only ride on relatively smooth trails and don’t do any serious downhilling, then chances are your chains will stay put without a guide.

Similarly, if your tires are always kept at high pressure (over 30 psi), then they’re less likely to come off the bead even if you hit some big bumps along the way. And finally, if your drivetrain is conventional (3×9 or 3×10), then it’s unlikely that you’ll ever have problems with dropped chains even without a guide. So there you have it – whether or not you need a chain guide on your mountain bike is largely dependent on what type of ridingyou do and what kind of equipmentyou have.

How to Put a Chain on a Mountain Bike - A Detailed Guide

Credit: biketoworkday.us

How to Put a Chain on a Bike With Gears

It’s a common misconception that you need special tools to put a chain on a bike with gears, but it’s actually quite simple to do. All you need is a chain, some grease, and a few minutes of your time. Here’s how to do it:

1. Start by putting the chain around the largest cog in the back (the cassette). Then thread it through the derailleur and up to the front chainrings. 2. Next, take the end of the chain and feed it through the gap between the two plates that make up the rear derailleur (this is called the pulley cage).

3. Now, pull on the chain until there is no slack left and then connect it to itself using one of the master links (or an old-fashioned rivet). Make sure that the link is tight against both plates before you continue. 4. Once your chain is connected, shift into each gear combination and make sure that there is no excessive noise or slippage.

If everything seems good, you’re done!

How to Put Chain Back on Mountain Bike

If your mountain bike chain has come off, don’t worry! It’s actually not that difficult to put it back on. Here’s a step-by-step guide on how to do it:

1. Start by putting the chain back on the largest cog on the rear cassette. This is usually the easiest place to start. 2. Then, work your way through the rest of the cogs, one by one, until you reach the smallest cog.

3. Next, thread the chain through the derailleur and onto the front chainring. Again, start with the largest ring and work your way down to the smallest ring. 4. Finally, connect the two ends of the chain together using a quick link or master link (depending on what type of chain you have).

Make sure that both sides of the link are facing inwards before you snap it closed!

How to Put a Chain on a Mongoose Mountain Bike

If you’re new to mountain biking, or even if you’ve been riding for a while, putting a chain on a Mongoose bike can seem like a daunting task. But don’t worry! We’re here to help.

Follow these simple steps and you’ll have your chain on in no time. 1. First, place your bike upside down so that the wheels are pointing up. This will make it easier to work on the chain.

2. Next, use a chain tool (or a pair of pliers) to remove the old chain from the bike. You’ll need to break the chain at one of the links. 3. Now it’s time to put on the new chain.

Start by feeding one end of the chain through the rear derailleur (located near the back wheel). Then run the chain through all of the gears on the cassette (the gears located on your rear wheel). Make sure that thechain is running smoothly through all of the gears before proceeding to step 4.

4. Once you’ve fed the chain through all of the gears, it’s time to connect it together again using a link pin or master link (depending on what type of chain you have). If you’re using a link pin, simply insert it into one of The Chain Links And Use Pliers To Squeeze It Together Until It’s Securely Fastened In Place; if you’re using a master link, follow The Instructions That Came With Your Chain To Connect It Properly . Whichever method you use, make sure that The Chain Is Not Too Tight Or Too Loose Before Proceeding To Step 5 .

5 Finally , re-attach The Chain Guard (if applicable) and turn your bike right-side up again . You’re now ready to hit The Trails !

How to Put Bike Chain Back on Derailleur

If your bike chain has come off the derailleur, don’t worry! It’s actually a pretty simple fix. First, you’ll need to find the master link.

This is the link that allows you to take the chain off without having to use a chain tool. Once you’ve found the master link, simply reconnect the two ends of the chain. Make sure that the master link is facing the right way before you try to connect it – otherwise, it won’t fit properly and you’ll have to start over.

Once the chain is back on, shift into each gear and make sure that everything is working properly. If your chain feels loose or falls off again, there may be an issue with your derailleur adjustment. Bring your bike to a qualified mechanic if this happens so they can take a look at it.

Mountain Bike Chain Guide

If you’re a mountain biker, then you know that having a good chain guide is essential. A chain guide helps to keep your chain from falling off of your bike, which can be a major problem when riding on rough terrain. There are a variety of different chain guides on the market, and it can be difficult to decide which one is right for you.

In this blog post, we’ll take a look at some of the things you should consider when choosing a mountain bike chain guide. First and foremost, you need to think about the type of terrain you’ll be riding on. If you’re only going to be riding on relatively smooth trails, then you probably don’t need a super heavy-duty chain guide.

However, if you’re planning on doing some serious off-roading, then you’ll want something that’s designed to withstand more abuse. Another thing to consider is the size of your bike’s drivetrain. Some chain guides are only compatible with certain types of drivetrains (such as 1x or 2x setups), so it’s important to make sure that the guide you choose will work with your bike.

Most manufacturers will list compatibility information on their product pages. Once you’ve considered these factors, it’s time to start looking at specific models. There are dozens of different options out there, so it’s important to do some research before making your final decision.

Read online reviews from other mountain bikers and look for products that have received high marks for durability and performance. With a little bit of effort, you should be able to find the perfect chain guide for your needs!

Conclusion

If you’ve ever wondered how to put a chain on a mountain bike, wonder no more! This detailed guide will walk you through the process step-by-step so that you can get back to riding as soon as possible. First, you’ll need to gather a few tools: a chain breaker, a master link, and a pair of pliers.

Next, remove the old chain from the bike using the chain breaker. Once the old chain is off, it’s time to put on the new one. Start by threading one end of the new chain through the rear derailleur.

Then run the chain around the gears in the front, making sure that it goes through all of the pulleys. Finally, connect the two ends of the chain together with the master link. Now all that’s left to do is give it a test ride!

Leave a Comment